Rms-technologies R325P DRIVER Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Software Rms-technologies R325P DRIVER. RMS Technologies R325P DRIVER User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 30
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
R325PE Single Axis Driver
with Indexer and Encoder Reader
User Manual
And Commands Guide
Version 1.01
RMS Technologies
2533 N. Carson St. #4698, Carson City, NV 89706-0147
RMS Technologies Page 1 Version 1.01
R325P Single Axis Driver Manual 5/29/2013
Zobrazit stránku 0
1 2 3 4 5 6 ... 29 30

Shrnutí obsahu

Strany 1 - R325PE Single Axis Driver

R325PE Single Axis Driver with Indexer and Encoder Reader User Manual And Commands Guide Version 1.01 RMS Technologies 2533 N. Carson St. #4

Strany 2

Figure 6.1 Using the R325P with more than 5V You can choose to supply the optos with the R325P’s internal 5V supply by jumping pins 1 to 4. But

Strany 3 - Updated enable/disable pin

Configure the R325P using the DIP Switch R325P DIP Switch Settings Run Current Function SW1 SW2 SW3 SW4 0.3A ON ON ON ON 0.4A OFF ON ON ON 0.5A ON O

Strany 4 - Table of Contents

Communicating with the R325PE Step 1: Move all dipswitches to the OFF position. Place jumper on Pins 1 & 2. Inage 6.3 1. Connect P1 to PC via

Strany 5 - 2. ELECTRICAL SPECIFICATIONS

USB485 Converter Card Figure 6.3 7. COMMAND TABLES The R325PE can also be used as an indexer with closed loop controls. Basic controller commands c

Strany 6 - 4. MECHANICAL SPECIFICATIONS

General Operation Commands Function Query/Command Code Value Minimum Maximum Default Absolute Position C AP Numeric -2,147,483,646 2,147,483,647 - Cu

Strany 7

8. COMMANDS Protocol Syntax Command Format: #<Address><Command><value><CR><LF> Example: #ACP1000<CR><LF&g

Strany 8 - 6. CONNECTION SPECIFICATIONS

Table 8.1 – List of Commands Command (Case Sensitive) Operand Example Description HOMING & POSITIONING HA 0 = Forward 1 = Reverse #AHA1 Motor

Strany 9 - Connecting the Motor

Command (Case Sensitive) Operand Example Description VELOCITY & ACCELERATION (cont.) AP +/–2,147,483,646 #AAP1000 Moves to the 1000th position.

Strany 10

Command (Case Sensitive) Operand Example Description VELOCITY & ACCELERATION (cont.) SB - #ASB Moves one step back Step Back - Command Only - M

Strany 11 - R325P DIP Switch Settings

Command (Case Sensitive) Operand Example Description SETTING CURRENT HI 0-3000 #AHI300 Sets the Hold Current to 300mA (0.3A) Hold Current - Comman

Strany 12 - RS485-232 Converter Card

Thank you for purchasing the R325PE Single-Axis Driver with Indexer. This product is warranted to be free of manufacturing defects for one (1) year f

Strany 13 - 7. COMMAND TABLES

Command (Case Sensitive) Operand Example Description SD - #ASD Saves data Save Data - Command Only - This command causes a set of parameter values

Strany 14 - Encoder Count

Command (Case Sensitive) Operand Example Description QUERY COMMANDS FR - #AFR Firmware Revision - Query Only - Returns 3 digit part code followed b

Strany 15 - 8. COMMANDS

Command (Case Sensitive) Operand Example Description ENCODER VERSION COMMANDS EM 1, 2 #AEM2 Sets the Encoder Mode to 2 Encoder Mode – Command or Q

Strany 16

ER 0 - 16777215 #AER *AER5 Error Read – Query Only - Returns the current Encoder Error value. If the product of Encoder Lines and Encoder mode is l

Strany 17

9. Troubleshooting R325P is not functioning correctly Try putting the R325P into TEST mode by placing a jumper on Pins 3 & 4 of J1 as shown bel

Strany 18

10. Appendix A: Recommended Cable Recommended Cable Configurations: DC Supply to Driver Cable length, wire gauge and power conditioning devices play

Strany 19

NOTE: These recommendations will provide optimal protection against EMI and RFI. The actual cable type, wire gauge, shield type and filtering devices

Strany 20

Recommended Cable Configurations: Driver to Motor Cable length, wire gauge and power conditioning devices play a major role in the performance of you

Strany 21

* 0.5 MH is a typical starting point for the Common Mode Line Filters. By increasing or decreasing the value of L you can set the drain current to a m

Strany 22

11. Appendix B: PF Value For applications requiring ultimate smoothness of motion and extreme accuracy, the R325P driver can be programmed via RS485

Strany 23 - Motion Profile Commands

R325PE User Manual Product: R325PE Version: 1.01 Date: 5/29/2013 Version History Version Date Description of Changes 1.00 01/31/2013 New User

Strany 24 - 9. Troubleshooting

• PF value 3 • Slow speeds • Bad waveform • PF value 1 • Fast speeds • Bad waveform RMS Technologies Page 30 Version 1.01 R325PE Sin

Strany 25

Table of Contents 1. FEATURES... 5 2. ELECTRICAL SPECIFICATI

Strany 26

1. FEATURES • Single Axis Driver with indexer for Bipolar step motors • Encoder readout function available • Operates from +12 to 48 VDC • Phase

Strany 27

3. OPERATING SPECIFICATIONS Maximum Step Frequency: 2.5 MHz Operating Temperature: Low end – 0° C High end – Dependent on case temperature, bra

Strany 28

5. PIN ASSIGNMENTS Mating Connectors P1 AMP 640441-3 P2 AMP 640441-5 P3 Phoenix 1803675 P1 – RS485 bus Interface P1 Configurati

Strany 29 - 11. Appendix B: PF Value

CAUTION: Connecting Motor phases (A, A Bar, B, B Bar) to the incorrect location while the R325P is powered will cause the board to burn. Be sure to i

Strany 30

Pin 6: Phase A Motor Connection Pin 7: Phase A Motor Connection Pin 8: Phase B Motor Connection Pin 9: Phase B Motor Connection CAUTION: Connecti

Komentáře k této Příručce

Žádné komentáře